The default installer code for a DSC is The installer code is the code that is used to get into the DSC programming mode so you can set the system up and make changes to panel programming. Having the installer code is the most important part of setting up the system.
You will not be able to arm or disarm with the system with the installer code. But if you have the installer code you can make any changes you want to the system, including changing the master code. The installer code, like the master code should ideally be changed to a number that is not easy to guess. While it is perhaps not as critical as changing the master code for security purposes, if someone has access to the system while it is disarmed and they have intentions to make changes having an installer code that is not the system default is important.
Product successfully added to your Shopping Cart. Continue Shopping. Proceed to Checkout. The module also has built-in two-way voice capability for central station See Section 5. Three additional devices are available These devices are not UL Listed :. The Door Box contains a relay so the normal door bell can be used instead of the internal one generated by the PC module.
This PC Printer Module will allow the panel to print out all events that occur on the system to any serial printer.
All events will be printed with the Partition, time, date and the event that occurred See Section 5. The unit comes in its own cabinet with antenna and requires a separate battery and transformer See Section 5. Several different cabinets are available for the PC modules. They are as follows:.
Dimensions mm x mm x There are two different backplates available for keypads to locate an Audio Station next to the keypad:. This backplate is to be used when an Audio Station is to be located next to a keypad.
You should find the following equipment included in your system. Verify each of the components is included:. The following sections provide a complete description of how to wire and configure devices and zones. The following steps are provided to assist with the installation of the panel.
It is suggested that you read over this section briefly to get an overall understanding of the order of installation. Once this is done carefully work through each step. Working from this plan will help reduce problems and reduce the overall installation time required.
Draw a rough sketch of the building and include all alarm detection devices, zone expanders, keypads and all other modules that are required. Locate the panel in a dry area, preferably located near an unswitched AC power source and the incoming telephone line. Before attaching the cabinet to the wall be sure to press the five circuit board mounting studs into the cabinet from the back.
Complete all wiring before applying AC or connecting the battery. If zone expander modules are being used the modules must be configured so the panel knows which zones are assigned to each expander.
Follow the guideline provided to assign zones to expanders. Power down the control panel and complete all zone wiring. Follow the guidelines provided in Section 2.
Complete all other wiring including bells or sirens, phone line connections, ground connections or any other wiring necessary. The panel will not power up if only the battery is connected. Keypads must be assigned to different slots to be properly supervised.
Follow the guideline provided in Section 2. After all modules have been wired to the Keybus, supervision must be enabled. Once supervision is enabled, the panel will be able to indicate module communication faults.
Section 4. Section 5. The Programming Work Sheets should be filled out completely before attempting to program the system. Test the panel completely to ensure that all features and functions are operating as programmed. The panel requires a Connect the transformer to an unswitched AC source and connect the transformer to these terminals.
Do not connect the transformer until all other wiring is complete. The battery is used to provide back up power in the event of an AC power failure and to provide additional current when the panel demands exceed the power output of the transformer, such as when the panel is in alarm.
Do not connect the battery until all other wiring is complete. These terminals provide up to mA of additional current at 12 V DC rated The AUX output is protected; if too much current is drawn from these terminals wiring short the panel will temporarily shut off the output, until the problem is corrected.
These terminals provide up to 3 Amps of current at 12 V DC rated The Bell output is supervised. The Keybus is used by the panel to communicate with modules and by modules to communicate with the panel.
Each module has four Keybus terminals that must be connected to the four Keybus terminals on the panel. For more information, see Section 2. Each PGM output is an open collector switch to ground. That is, when the PGM output is activated by the panel the terminal will switch to ground. If more than 50 mA of current is required a relay must be used. Refer to the following diagram:.
It can be used for two wire smoke detectors See Section 2. Otherwise, the CON1 must remain on at all times. Each detection device must be connected to a zone on the control panel. It is suggested that each zone have one detection device however it is possible to wire multiple detection devices to the same zone. For zone wiring specifics, see Section 2. If a telephone line is required for central station communication or downloading, connect an RJX jack in the following manner:.
Ensure the plugs and jacks meet the dimension, tolerance and metallic plating requirements of 47 C. Part 68, SubPart F. For proper operation there must be no other telephone equipment connected between the control panel and the telephone company facilities. Do not connect the alarm panel communicator to telephone lines intended for use with a FAX machine. These lines may incorporate a voice filter which disconnects the line if anything other than FAX signals are detected, resulting in incomplete transmissions.
The Keybus is used by the panel to communicate with all modules connected and by the modules to talk to the panel. The 4 Keybus terminals of the panel must be connected to the 4 Keybus terminals or wires of all modules. In order for the Power system to operate properly, the power output capabilities of the main control and expansion devices must not be exceeded.
Use the data presented below to ensure that no part of the system is overloaded and cannot function properly. Includes one keypad. Short Term. Available only with stand-by battery connected. Continuous Rating. Subtract for each device connected. Subtract the total load on this terminal. Do not allow connected devices to exceed the system capabilities during any possible operational mode. The main panel contains zones 1 to 8. Additional zone expanders may be added to increase the number of zones on the system.
Each zone expander consists of two groups of 4 zones and each group must be configured to assign the specific zones to the expander. This is done by setting the jumpers located on the expander to the proper settings. Before a zone expander will work properly the jumpers must be set so the panel can determine the correct zone assignment.
The following is a diagram of the zone expander and where the jumper switches are located. There are two sets of jumpers, one set for the first 4 zones of the expander and one set for the other 4 zones. In this diagram the jumpers settings shown indicate the first group of four zones of the expander will be zones 9 to 12 and the second group of 4 zones will be 13 to In the above diagram the jumpers settings shown indicate the first group of four zones of the expander will be zones 9 to 12 and the second group of 4 zones will be 13 to There are 8 available slots for keypads.
Keypads can each be assigned to a different slot 1 to 8 which offers two advantages. The panel can supervise the keypad connection to indicate a trouble condition if it is removed. Also keypads can be assigned to operate a specific partition or operate as a global keypad. All keypad assignment must be done individually on each keypad on the system. To assign a keypad to a slot and select the partition it will operate, enter the following: Step 1 — Enter Installer Programming.
Enter a two digit number to specify the partition and slot assignment. Press the [ ] key twice to exit programming. Continue this procedure at each keypad until all have been assigned to the correct slot.
Each of the 5 Function Keys on each keypad may be programmed for different operation on each keypad. For a complete list of Function Key options See Section 3.
Once all the Keybus connections have been made, supervision must be enabled so the panel can indicate a trouble if a module is removed from the system. Step 2 - Press [] to enable supervision.
The panel will automatically search for all modules on the system. Once the search it will take about 1 minute is complete enter the following to confirm the modules on the system. Zone lights will be turned on according to what modules the panel has found on the system. The LCD keypad will allow you to scroll through the modules. Refer to the following chart:. If a module is connected but does not show as being present, it may be due to any of the following reasons:.
If a module is no longer required on the system the panel must be told to no longer supervise the module. To do this remove the module from the Keybus and perform the Enable supervision function again See Section. The panel will see the module has been removed and will no longer supervise it.
For a complete description of the operation of all zone types, please refer to Section 5. There are several different ways in which zones may be wired, depending on which programming options have been selected.
Please refer to the following diagrams to study each type of individually supervised zone wiring. Any zone programmed for Fire or 24 Hour Supervisory must be wired with a single End of Line EOL resistor regardless of the type of zone wiring supervision selected for the panel section [], options [1] and [2].
See Section 5. If you do not, the zones may not work correctly. To enable normally closed loops, programming section [], option [1] must be ON. This option should only be selected if Normally Closed NC detection devices or contacts are being used.
To enable panel detection of single end of line resistors, programming section [], options [1] and [2] must be OFF. Double End of Line resistors allow the panel to determine if the zone is in alarm, tampered or faulted.
To enable panel detection of double end of line resistors, programming section [], option [1] must be. This option can only be selected if Normally Closed NC detection devices or contacts are being used. Only one NC contact can be connected to each zone. Wiring multiple detection devices or contacts on a single loop is not allowed. All zones defined as Fire See Section 5.
For a complete description of how fire zones operate, see Section 5. For a complete description of how fire zones operate, see. Zones may be programmed to be used as keyswitch arming zones and must be wired according to the following diagrams:.
For a complete description of how keyswitch zones operate, see Section 5. Program this zone as zone type [09], 24 Hour Supervisory in section []. With a 24 Hour Supervisory zone, if the LINKS experiences a trouble, the zone will be violated, causing the panel to report the event to the central station.
Wire this zone according to the diagram. Keypads with zone inputs can be connected to devices such as door contacts. This saves you from running wires back to the control panel for every device. To install the keypad, open the keypad plastic by removing the screw at the bottom of the unit.
Locate the five terminals on the keypad circuit board. Connect the four Keybus wires from the control panel: the red wire to R, the black to B, the yellow to Y and the green to G. To connect the zone, run one wire to the Z terminal and the other to B. For powered devices, use red and black to supply power to the device. Run the red wire to the R positive terminal and the black wire to the B negative terminal. When using end of line supervision, connect the zone according to one of the configurations outlined in Section 2.
Keypad zones do not support DEOL resistors. First, ensure that you have enrolled all installed keypads into the desired slots. See Section 2. Next, enter programming section [] to assign the zones. There are eight programming locations in this section, one for each keypad slot. Enter a 2-digit zone number for each of the keypad zones. This number must be entered in the location corresponding to the keypad to which each zone is connected.
Once the keypad zones are assigned, you must also program zone definitions and zone attributes. See also Section 5. All keypads provide complete information and control of the alarm panel. The panel can be completely programmed via any keypad on the system. LED keypads provide function indicator lights and individual zone indicator lights for the alarm circuits.
The LCD keypad provides function indicator lights and word descriptions for zone status. The following sections describe how to arm, disarm and perform other keypad functions. This will prevent the user from being able to change the System Master Code. If they attempt to change the code the keypad will sound a long error beep. The System Master Code can be used to arm or disarm any partition and perform any keypad function. By default the Partition Master Codes are not programmed.
They must be programmed by the System Master Code. A Partition Master Code, when first programmed, can act as a second master code and have the same access as the System Master Code.
A Partition Master Code can program the access codes to operate on the Partition it is assigned to and program the Partition Duress Code.
By default Partition Duress Codes are not programmed. Once programmed if the Duress Code is used any time, the panel will activate a silent Duress alarm See Section 5. By default the 32 User Codes are not programmed. Once programmed the User Code can be used to arm or disarm any partition it is enabled for.
Each User Code can be enabled or disabled for bypass ability, or remote access to the Escort See Section 3. It cannot be used to bypass zones. This code cannot be used to access the system by the Escort The code can be used for service personnel. As each digit is pressed the keypad will beep. If an incorrect code is entered the keypad will emit a steady 2 second beep to indicate the code was not correct.
Other methods of arming are available See Section 3. The keypad will emit a steady beep to warn that you must disarm the system. During the last 10 seconds of entry delay the panel will pulse the keypad beeper on and off rapidly to warn the entry delay is about to expire. Enter a valid Access Code at the keypad. If an error is made, re-enter the code correctly.
0コメント